Optima Instruments

• Digital temperature controller cum indicator with Timer.
• Low water level indication with audio alarm.
• Fully automatic Autoclave with printer interface through RS232 / Rs485. For multiple networking.

• Digital control-easy to use
• Totally unobstructed, crevice free
• Stainless steel tank-corrosion resistant and easy to clean
• Sturdy construction-stainless steel 304 inner and outer chamber
• Standards accessory-concentric rings and steel lid
• Optional heater cover and low water level alarm

• Ideal for flocculation testing in water treatment laboratories Digital control using microprocessor
• Geared DC motor and specially designed timing belt
• Stable and accurate stirring speed max 300 rpm
• Storage function for set values: rpm and timer Illumination flourescent lamp
• 4 paddle stainless steel shaft

Quality Control:

• Temperature test of each compartment
• Insulated test
• Pressure test of refrigeration system
• Overloading & Overheating tests with difference voltage and cycles.

Ultra Low Temperature Freezer:

• Ideal instrument for laboratories
• Hydraulic thermostat control
• Heater on indicator

• Standard Model- time proportional ON/OFF controller cum indicator
• Micro controller based PID controller cum indicator.
• Controller with Printer Interface as optional.
• Controller Interface through Rs 232C/RS 485 for multiple networking.
• FEATURE (OPTIONAL FOR GMP/ICH MODEL)
• ICH Guide Lines followed.
• S.S. removable to prevent over shoot.
• Safety thermostat to prevent over shoot.
• HRC fuse for all controls.
• Bacterilogical incubator are non refrigerated version for temp. Range of ambient +5°C to 60°C

• Capacity Cuft: 3
• Volume LTR.: 90 to 450
• Approx.Inner W X D X H (cm): 40 X 40 X 57
• No of Shelves: 2-3/5
• Temp Range: 50 to 600 C
• Temp Accuracy: man Old Style; font-size: small; >50C

• Economic magnetic stirrer with stainless steel heating plate.
• DC motor for higher torque at low speed
• Better low speed stirring even with small volume
• Accurate stepless speed control maintains excellent speed stability
• Specially designed for corrosive atmosphere reducing the chances of fumes entering the unit
• Spillage collection tray with drain outlet

• Stirring quantity (h2o) L.: 05
• Electrical Supply: 230 v DC 50 Hz single phase

Horizontal Autoclave semi automatic with 20litres of capacity used in laboratories and pharmaceuticals.

• Hi-tech Vacuum Oven Double walled
• Inside-cylinder is made of thick stainless steel 304 Qty. And outside Ms powder coated.
• High grade mineral glass wool insulation the walls to avoid energy loss.
• Temperature range from 50°C to 230°C with ±2°C accuracy.
• Temperature controlled by Digital temp. Controller cum indicator.
• Vacuum chamber is wrapped with a set of high quality heaters for quick and uniform heating.
• Door has a thick toughened glass window, perfectly sealed with silicon gasket for thermal condition.
• Specially designed per-treated Aluminum door has a screwed door closure.
• Proper door alignment to ensure excellent vacuum performance and operator’s safety.
• Two removable stainless steel shelf.Z
• Designed to be operated at any pressure less than atmospheric pressure

• Control by Microprocessor based PID controller.
• Computer interface RS 485 / RS 232 interface for multiple / single communication port with printer.
• Safety device Thermostat or Energy Regulator for over heating.
• Complete Stainless steel 304/316 Qty. contraction.

• Desiccator :- Polycarbonate
• Body :- fully stainless steel. 304

• Extremely “compact” construction
• Diaphragm type vacuum pump
• Polycarbonate vacuum desiccator
• Stainless steel (GMP) construction
• Vacuum level up to 22’ of Hg

• On-line monitoring the conductivity and temperature of RO pure water;
• Online monitoring UP ultrapure water resistivity;
• Automatic flush the RO membrane by the system;
• Dispense water at a fixed time and volume set by the user(while there is water storage in reservoir);
• The quality of purified water is enhanced by the internal recirculation system;
• Automatic flush the RO membrane by the system;
• Historical data enquiry;
• Benchtop with 10-inch Pretreatment Cartridge in standard configuration

• Digital Display Electronic Temperature cum R.H.
• Heat up time: 30min. up to + 600 C. without load
• Cool down time: 30min. up to + 600 C. without load
• Inner Acrylic Door: Inner Full Size Through Acrylic 8mm thick

• 16 x 2cm Large size numericl LCD display
• Fully Micro controlled operation
• Continues display of process valve along with vacuum level
• Vacuum and time be programmed

• The holdmode is divided into the following
• Evacuation of the desicator The test time for vacuum exposure will stress the package to exact periods venting the desiccator
• The blister pack remains under atmospheric pressure. This ensures that the day penetrates into fine capillaries.

• Vacuum source: Inbuilt double-headed membrane vacuum pump
• Supply voltage: 230 V AC
• Frequency: 50/60 Hz
• Pressure units: mmHg
• Vacuum: adjustable up to max 600mm
• Temperature: ± 5 to + 400 C
• Air RH: 0 to 90% non condensing

• Control Soft Touch up down key
• Shaking Frequency./min: 10 to 250 rpm
• Shaking amplitude, mm.: 10.20, 30 mm
• Mass 9 without attachments ,kg: 35 kg

• General mixing
• General mixing
• Cell cultures
• Extraction procedure
• Staining destaining
• Hybridisation
• Diagnostic test
• Solubility studies
• Bacterial suspensions
• Washing procedures

• High stability four column load frame
• Each frame tested for stability and alignment to avoid tension failure during a test and to ensure center loading
• Standard Platens for 3 X 6”/ 4 X 8” and 6 X 12” cylinders included.
• A precise large diameter spherical upper platen for optimum results
• Variety of optional accessories for cubes, blocks, bricks and flexure test available
• Motorized hydraulic power pack or pumping unit with rapid approach and automatic over load protection
• Comes standard with safety Guards on all four sides.

• The Complete unit comprises a Loading Unit which is of fully welded or two pillar model construction having a cross-head with a spherical seated platen. The lower platen is attached to the top of the piston. The Loading capacity is of 2000 KN, Cubes up to 200 mm & Cylinders up to 150 mm Dia X 300 mm Height can be tested using the appropriate spacers.
• Pumping Unit with choice of compact power pack attached closely to the loading unit or separate hydraulic pumping unit, attached to the loading unit by high pressure hydraulic flexible hose pipe. The pump facilitates rapid approach of the platens for daylight closure and also provides comprehensive control over the application of load. A control valve provides fine control over the loading rate for accurate pacing.
• Maximum load is held and retained for approx. 15 min, unless cancelled, using the panel mounted reset switch. Pace rate set for running the test can be maintained manually.

• Indicating four value at a time as follows.
• Current load on the sample in KN.
• Load per unit area in kg./cm square.
• Load per unit area in N/mm square.
• Direct display of maximum load retention.
• It is having facility to insert the sample size, e.g
• If sample of cube size is 150 mm x 150 mm x 150 mm , the value can be entered in load indicator so that we can directly get load per unit area continuously on line, so no calculation for unit load require.
• We can store value of last 10 memories.
• We can measure rate of loading per minute by simply pressing one button.
• It can be connected with computer for auto report generation as well as to derive graph of load versus time.
• Motor can be directly start or stop by load indicator.
• It disconnects the current to the motor at the time of overload to specified maximum load.
• The range of load indicator can be set automatically from 50 kn to 2000 kn according to the requirement of range.
• Facility for auto-calibration by default value.
• The controller is having least count of 1 KN. (I am planning to upgrade for 0.5 KN)
• It is having facility for bar graph which will automatically blink to its full length according to the rise of rate of loading.

• Shelves shall be supplied with above ovens of galvanized wire mesh.
• Shelves made of stainless steel will be supplied at extra cost.
• Air forced circulation fan can be supplied at extra coast for better accuracy
• We can fabricate any size of oven as per customer specification.
• PID microprocessor temperature controller cum indicator.
• Controller Interface through RS232C / RS 485 for multiple networking

Inside Size (Diaxdepth) : Rate

• Round : 225 x 300 m.m. (9"x12")
• Round : 300 x 375 m.m. (12"x15")

Product Specifications

• Temperature: 00C to 800C (with Cooling)
• Temp. Control: By P.I.D. Controller
• Temp. Accuracy: Better than ± 0.30
• Circulation: By Inbuilt circulation
• Flow rate: 10 -15 liter / minute – continues
• Size: A) Minium size -150 x 300 x 250 mm,B)-450 x 300 x 550 mm

• A Sleek and sturdy Innovative design
• Smooth start and stop
• Higher speed range constant torque with precise speed control
• Maintainance and spark free PMDC motor
• Digital speed display
• Digital Feedback speed controller with timer

• Designed as per ICH guidelines to meet, WHO and USFDA requirement
• Fulfills storage conditions of 25° C - 60% RH, 40° C - 75% RH, 30° C - 65% RH, 25° C - 40% RH, 30° C - 35% RH
• Temperature Accuracy : ± 1.0° C
• Temperature Resolution : 0.1° C
• Himidity Fluctuation : Maximum 3% RH
• Chamber lllumination : With 2 or 4 LED lights for lesser power consumption
• Overall Power consumption : 2.5 KW Per phase (For 3 - phase connection)