Optima Instruments

New Enhanced Alcohol Detector

Model: IBlow10

Brand: SENTECH KOREA

Special Features:

·         New advanced highly sensitive SuracellTM sensor technology (Fuel Cell sensor)

·         With PC Connectivity

·         12 people can be measured per minute

·         No mouthpiece required. Instead replaceable & washable Blow Cap provided for hygienic use

·         No calibration required until 5000 tests or 1 year, whichever is earlier

·         Reminder for Calibration & Grace period

·         LED Light Alerts (Red for Fail & Green for Pass)

·         Display Window Provided

·         Manual Sampling Function (Alcohol content in Liquid can be measured)

·         Slow and Fast Measuring Modes available

·         Adjustable Display and Power Off time

·         Built-in Magnet attachable to Vehicles

• Free chlorine, total Chlorine measurement.
• Range : Auto range.
• Measuring principal : Photo meter method.
• Record Max, Min. value.
• 10 PCs Free and Total powder DPD are included.
• Free and total 1.0 mg/L standard solution are the standard accessories.
• The measuring method is an adaptation of the USEPA Method 330.5 and Standard Method.

• No. of Channels: 1
• RPM: 0.01 to 0.99
• Flow rate: 0.002 ml to 1 ml/hr
• Tubing: mm to 3 mm ID with 1 to 1.5 mm wall thicknesss
• >Motor: DC stepper motor (Cont. duty)

Application:

Peristaltic Pumps are the simplest possible pumps, with no valves and seals. The fluid contacts only the tubing, eliminating the risk of the pump contaminating the fluid, or the fluid contaminating the pump. Peristaltic pump can operate dry without risk. Backflow and siphoning do not occur.

The flow rate depends mainly on the internal diameter of the tube and the speed at which the roller advance. Suction lift capability depends on the restitution power of the tube. The best way to select the tube is first determine which materials are chemically suitable and then to choose the one that best matches of significant pressure, suction or vacuum demands.

• Temperature Range : 5ºC Above Ambient to 300ºC
• Heating before set point : Automatic Temperature Heating depending upon temp. diff.
• Heating after Set point : Variable 0.5, 1.0 2.0 ºC/min – Selectable
• Detection of Melting : Melting Range
• Temperature Resolution : 0.1ºC
• Calibration: Multipoint Point Calibration Standard – as per Pharmacopia or any users known standard.
• Melting Capillary : Three Capillary
• Sample : Borosilicate Capillary Tube One End Sealed
• a) OD : 1.4 to 1.6 mm b) ID : 1.0mm c) Filling Height : 3 mm
• Temperature Sensor : PT-100
• Data Storage: Non Volatile Memory with more than 50 analysis data storage with corresponding calibration data.
• Method Storage: Ten User method parameter with Add/Edit Facility.
• Printer Output : Parallel Port (Optional)
• Keyboard : Alphanumeric Polyester Softkeys
• Backlit LCD Display : 20 x 4 Line Alphanumeric
• Power : 230 VAC ± 10%, 50Hz

• Built in Magnetic Stirrer with soft touch Key Speed Controller with audio sound.
• Automatic Temperature Heating depending upon heating requirement.
• Electronic Temperature Regulator to increase / decrease heating rate.
• Facility to enter set temperature by using soft touch keypad.
• Soft Touch Keypad to prevent contact problem.
• Over heating protection by heater cut-off.
• On-site Temperature Calibration by Calibrated Thermometer / Calibration standards.
• Re-Call Default factory set calibrated temperature data.

• Camera attachment
• Parallel Port for Dot matrix Printer attachment
• RS-232 to USB Interface with Cable Driver Software to Transfer Data From Inst. to PC

• Drinking Water
• Waste Water
• Cooling/Boiler Water
• Pool Water
• Surface Water
• Water Treatment Companies
• Industrial and Governmental Laboratories

• Solid state circuit design
• High degree of accuracy 0.01 pH
• High input impedance
• Check facility for quick analysis
• Non flickering display
• Built in stabilizer
• Auto polarity decimal
• Compact light in weight

• 0.01 pH ± 1 digit
• 1 mV ± 1 digit
• Input Impedance
• 1012 Ohms

• Range: 0.00 to 14.00 pH
• Temperature Control: 0 to 100°c Manual
• Display: 3.5 digit LED display with auto polarity decimal
• Calibration: Two buffers calibration (manually) 7pH 4pH Or 9.2pH
• Power Requirement: 230V A.C ± 10%, 50Hz single phase
• Weight: 1.5kgs (Approx) including accessories
• Standard Accessories: PH Electrode, Stand, Rod, Clamp, Buffers, Dust Cover Manual

• pH OI – 101: pH Mode
• Accuracy: 0.05 pH ± 1 digit
• Input Impedance: 5 x 1011 Ohms
• Temperature Control: 0 – 80°c Manual
• Calibration: Two buffers calibration (manually) 7pH,4pH Or 9.2pH
• Power Requirement: 9V dry cell flat pack Battery
• Environment: 5 to 50c
• Standard Accessories: PH Electrode, Buffers

• Mea­sure­ment with in­frared light at an angle of 90°
• Mea­sure­ment of coloured liq­uids
• Easy han­dling

• Direct sample selection
• Accurate and direct display of BOD values in mg/l
• User-friendly handling
• User-selectable measuring period from 1 to 28 days (BOD5, BOD7, OECD…)
• Storage of all values
• Auto start function after temperature equalisation
• Mercury-free, environmentally-friendly
• Inductive stirring system with automatic re-centering of stirring rods

• Automatic temperature compensation.
• 1600 Data logger point.
• Optional data transmition software, SW-DL2005.
• Separate probe, easy operation.
• RS-232 interface, Record (max., min.)

• Maximum, Minimum , Memory recall button.
• DO, Oxygen in air, Temp., ATC, Auto Cal., % salt.
• Diaphragms electrolyte included.
• Probe head with diaphragm set and electrolyte are included.

• No. of Channels: 1
• RPM: 4 to 60 (With direct digital display readout)
• Flow rate: 0.1 ml to 50 ml / min
• Tubing: 1 mm to 3 mm ID with 1 to 1.5 mm wall thickness
• Enclosure: Powder coated aluminium
• Motor: Permanent magnet DC motor (Cont. duty)
• Pressure: Upto 1.5 kg / sq. cm.
• Supply: 230 v, 50 Hz, Single phase AC
• Dimension: 110 x 170 x 175 mm (H x W x D)
• Weight: 4 Kgs (App.)

• Range: Four selectable ranges For TDS 20ppm, 200ppm, 2ppt 200ppt or for conductivity 20µ/cms, 200µ/cms, 2mili 200mil
• Measuring Accuracy: ±1% of F.S. ± 1 digit @ 25°C
• Calibration: Single Point Manually
• Cell: 1.0 Cell constant ± 10% (Platinum Cell)
• Power Requirement: 230V A.C ± 10%, 50Hz single phase
• Environment: 5 to 50°C
• Standard Accessories: Cell, Stand, Rod, Clamp, Dust Cover Operation Manual

• Range selection: Automatic / manual
• Range auto selection: 0 to 1999 millis/cm
• In 7 steps from 0-1.999 micros/cm to 1999 millis/ cm FSD.
• Readout: 3 ½ digit display with auto dot selection as per range selected
• Accuracy: +0.5% of full scale
• Test frequency: 200 Hz or 3 KHz selected automatically to get optimum reading
• Indications: Direct digital readout specific conductance in micro/ cm or millis/cm on a
• 3 ½ digit display with range indication by multi coloured LED S.
• Cell constant: Adjustable between 0.001 to 1.999
• Temp. Compensation: Manual/Automatic
• Recorder Out put : 1.999 volts FSD
• TDS Range: 0 to 1.32×106 ppm
• Dimensions: 260x280x65 mm
• Weight: 1.7 kg
• Power requirement: 230VAC+10% 50 HZ
• Standard supply: Basic unit, dust cover operation manual
• Essential accessory: conductivity cell of constants 1.00 to 0.10 at an extra cost,
• Optional accessory: Temperature compensator at an extra cost.

• Auto/SemiAuto/Manual mode of Operation Switches for adjusting the batch volume, Interval time etc. Provision for external
• ON by means of a proximity/Optical sensor for synchronizing with Conveyor system Inbuilt Drip back facility

• Circuit Custom one-chip of microprocessor LSI circuit.
• Range 0.00 to 50.00 NTU, 50 to 1,000 NTU
• NTU : Nephelometric Turbidity Unit
• Auto range
• Accuracy ± 5 % F.S. or ± 0.5 NTU, which ever is greater.
• Light source LED, 850 nm.
• Detector Photo diode
• Standard Meet ISO 7027.
• Response time Less than 10 seconds.
• Sample volume needed 10 mL.
• Data Hold Freeze the display reading.
• Memory Recall Maximum Minimum value.
• Display Sampling Time Approx. 1 second.
• Power off Auto shut off saves battery life or manual off by push button.
• Calibration points 0 NTU, 100 NTU.
• Operating Temperature 0 to 50 ???.
• Operating Humidity Less than 85% R.H.
• Power Supply DC 1.5 V battery ( UM4, AAA ) x 6 PCs, or equivalent.
• Power Current Stand by Approx. DC 3.5 mA.
• Testing Approx. DC 36 mA.

• Adopts UniBloc, which provides excellent impact resistance, responsiveness, and stability
• Equipped with the Easy Setting function, so responsiveness and stability can be adjusted during measurements
• Buy a separately available I/O–RS cable to import the results to a PC
  (Equipped with the Balance Keys function)

• Multiple Operating Valve: To carry out all functions of sterilization cycle at one point i.e. steam to jacket, steam to chamber, fast/ slow exhaust and vacuum/ drying
• Door: Single door shall be fitted with radical shooting arm, provided with automatic pressure locking device so that the door can not be opened till chamber pressure is fully exhausted
• Quick Vacuum Drying Apparatus: This Allows the filtered and sterilized air to break the chamber vacuum & helps in quick-drying
• Accidental Vacuum Breaker: A safety device so jacket against accidental vacuum in it and to remove residual air from it
• Safety Valve: A safety device against excess pressure in jacket and steam generator
• Electrical Control Box : Equipped with air break contractor of ' CUT. HAMM' make, toggle switch and two nos. indicating neon lamps
• Dial Type Thermometer: Indicates sterilization temperature

• ST-COD sealed tubes ready for use
• Sup­pres­sion of chlo­ride in­ter­fer­ence up to 1000 mg/l
• 3 ranges:
• Low range: 0 – 150 mg/l, meets ISO 15705:2003-01
• Mid­dle range: 0 – 1500 mg/l, meets ISO 15705:2003-01
• High range: 0 – 15000 mg/l

• Real time data recorder, save the data into the SD memory card and can be download to the
• Excel, extra software is no need.
• Auto temp. compensation, Auto Calibration.
• % salt and height value compensation adj..
• The polarographic type oxygen probe with an incorporated temperature sensor.
• Probe head with diaphragm set and electrolyte are included.
• Record (Max., Min.), Data hold, zero adjust.
• Patent: Taiwan, China, Japan, Germany, USA pending.

• Range : Na, K, Li :1-100 ppm and Ca:15-100 ppm
• Sensitivity : Na, K, Li :0.5 ppm and Ca:15 ppm
• Linearity : < 3%
• Reproducibility : 2% CV for 20 samples
• Detector : Photo Cell
• Ignition System : Manual Ignition
• Flame System : LPG Dry Oil Free Air
• Gas Control : Adjustable with Knob
• Automiser : Axial Flow Type
• Oil free Air Compressor : Supplied with Built-in Air Filter with Pressure Regulator Gauge to deliver stable and moisture / oil free air supply.
• Power Supply : 230 VAC ±10%, 50 Hz

• Li Filter
• Ca Filter
• Auto shut off at power off for LPG Gas Line

• Capacity: 120 gm to 310 gm
• Readability: 0.1mg to 0.001 gm
• Repeatability (+/-): 0.1mg to 0.001 gm
• Linearity (+/-): 0.2mg to 0.002 gm

• Easy to read green VFD Display
• Rugged, durable housing
• Stainless steel weighing pan
• Glass chamber with 3 way accessibility
• Level bubble and adjustable feet

• Back-light LCD display for easy viewing
• Piece counting % percentage weighing function.
• In-built rechargeable battery for continues use.
• Latest designed, space saving.
• Latest technology which doesn’t require worm-up time.
• In-built re-chargeable battery back-up

• Peristaltic, Self priming
• Switches for Flow Rate, Sample size, Sampling frequency and Interval time selections
• Facility to keep 1 Lit sampling bottle inside the unit

• High resolution up to 380,000 counts.
• Bright displays for easy viewing function.
• Built in rechargeable battery for continues use.
• Optional remote display available for customer.
• Environmentally protected load cell.
• Back rail support provided.
• Rugged construction suitable for industrial environment.